Skip to content

homepage / products / Product details

Ready-to-use nutrient media

Swarm agar

Article number

TN1702

contents

20 tubes

shape

fest

Storage temperature

2-8 °C

Product description

Purpose
The swarm agar enables the swarming of salmonella for the optimal expression of Salmonella H (chisel) antigens.

Test principle 
The swarm agar has a reduced agar concentration (approx. 0.6 %), which allows the Salmonella to swarm and which leads to a better formation of the H antigens. A complete formation of the H antigens is a prerequisite for the determination of the H antigens with corresponding H-specific anti-Salmonella test reagents.

Application and further information

1. Production of swarm agar plates
The tubes containing the swarm agar (10 ml) must be liquefied before use, e.g. in a pot of boiling water (approximately 10 min). Then it is cooled to about 40...45 °C and the contents of a tube are poured into a sterile petri dish with a diameter of 6 cm. The agar plates can be stored for up to 14 days at 2...8 °C (protect from drying out).

2. H antigen determination
Under aseptic conditions, the agar surface is wetted with approximately 100 μl sterile aqua dest. Of which Salmonella-Stem is taken some colony material and applied in a point-like manner in the center of the plate. The plate is incubated with the agar layer downwards for 16-20 h at 35...37 °C. For slide agglutination, the material is removed from the edge of the plate.

3. Phase induction
In the case of diphasic strains in which only one H-phase can be detected, a phase induction procedure must be carried out to form the second phase.

3.1. Sven Gard swarm inhibition method (classical method)
Mix 100 μl test reagent Anti-Salmonella H with 10 ml of liquefied swarm agar cooled to 40...45 °C in a sterile Petri dish of 6 cm diameter. After solidification of the agar, the plate is wetted with Aqua dest. as indicated under 2., inoculated with the Salmonella strain, incubated and the slide agglutination is carried out. If the phase induction does not succeed, the inhibition procedure must be repeated.

3.2. Simplified procedure
In addition to the classical method, the following alternative method can also be performed: On the surface of the swarm agar plate, 100 μl test reagent Anti-Salmonella H is dripped and distributed with a sterile spatula. Then the middle of the plate is inoculated and incubated as above.
After 16-20 hours, the swarmed trunk can be used to identify the second, uninhibited H-phase. The simplified procedure, when using the monoclonal test reagents, usually allows the detection of the second phase on the first attempt.

Interpretation of analytical results
On the swarm agar, the almost invariably scourged salmonella does not grow in colony form, but spreads from the vaccination site swarming to the plate periphery. If the strain is not sufficiently swarmed, the test should be repeated.

characteristics

contents20 tubes
Storage temperature2-8 °C
storagelight-protected
shapefest
clue1 tube contains 10 ml of culture medium.

Documents & Downloads

Here you will find the available product documents and batch documents.

AllInstructions for useSafety assessment

Instructions for use2 languages

PDF
Situation as at 10 June 2022
languageENDE

Safety assessment2 languages

PDF
Situation as at 05.10.2022
languageDEEN

Batch documents

Enter the full batch number to view the related documents.

Questions about this product?

Do you have questions about the selection, application or product documentation? Our team is happy to support you.

Personal advice

We will help you further

Your inquiry about article TN1702

Other products in this area

Acetamide solution

Acetamide solution

Article number: TN1512

Content: 20 x 1 tube

Acetamide solution

Acetamide solution

Article number: TN1512-01

Content: 100 x 1 tube

Agar for Microbiology

Agar for Microbiology

Article number: TN1400

Content: 500 g